시스코(CISCO) 스위치 WS-C2960S-48TS-S & WS-C2960S-48TS-L 모델의 명령어 차이

2019-04-25 KENNETH 0

운영중인 장비중 일부는 사양이 거의 같지만 모델이 약간 다름 무심코 기존에 사용했던 명령어로 설정을 하고 있었는데 동일한 SW버전( Version 12.2(55r)SE ) 라도 장비에 따라 다름 일부 명령어 운용에 차이가 있었던 것임 (전체 확인은 되지 않음) 발견된 내용 명령어 : interface 1. 기가비트이더넷의 1~44 번포트를 범주로 지정시 WS-C2960S-48TS-S : interface range GigabitEthernet 0/1-44 WS-C2960S-48TS-L : interface range GigabitEthernet 1/0/1-44 2. 기가비트이더넷의 단일 포트를 지정시 WS-C2960S-48TS-S : interface GigabitEthernet0/43 WS-C2960S-48TS-L : interface GigabitEthernet 1/0/43

프로그램 설치 없이 인터넷 속도 측정 하는 사이트

2018-09-26 KENNETH 0

가끔 사용중인 인터넷의 속도가 느릴 경우.. 이것이 내 환경의 문제 인지 아니면 저 서버의 문제 인지 즉각 판단이 어려운 경우가 있다.. 이럴 때 문득!!! 인터넷 속도좀 측정 해 볼까?? 싶지만… 매일 하는 것도 아니고, 그나마 어쩌다 한번씩 하는 요놈의 테스트는 뭔 놈의 프로그램을 그리 깔아야 하는지.. ㄷ ㄷ ㄷ   그런데!!!! https://www.speedtest.net/ 요런 사이트가 있었다.. ㅎㄷㄷㄷ 접속 후 “GO” 버튼만 누르면 끝! 물론 프로그램 설치 따위는 필요가 없다는 것!!!!! 두둥!!!!! 먼 훗날.. 내가 쓴 이 글을 나 자신이 기억 할 수 있을까 싶지만.. 우선 적어 놓는다…

No Image

Support for SATA and SAS disk drives with a size of 2TB or greater

2017-07-06 KENNETH 1

Support for SATA and SAS disk drives with a size of 2TB or greater URL : http://ask.microsemi.com/app/answers/detail/a_id/17414/~/support-for-sata-and-sas-disk-drives-with-a-size-of-2tb-or-greater   What is the current support for greater than 2TB SATA and SAS disk drives and Adaptec controllers? This information applies to the following Operating System(s): – This information is not Operating System specific The table below contains a list of Adaptec products and their status: Note: newer 6Gb/s and 12Gb/s disk drives may not be supported with backplanes rated at lower transfer rates. If in doubt, please check with the backplane manufacturer for the specific configuration details. Controller Size 2TB Size 3TB Size 4TB Size 5TB Size 6TB Size 8TB Series 8, 8Q tested tested tested tested tested tested Series 7, 7Q tested tested tested tested tested tested Series 7H, 6H tested tested tested tested tested tested Series 6, 6E, 6T, 6Q tested tested [ more… ]

No Image

FortiGate configure manage ip on CLI

2016-03-15 KENNETH 0

Using the CLI to configure Transparent mode Start a terminal emulation program (HyperTerminal) on the management computer. Use these settings: Baud Rate (bps) : 9600 Data bits : 8 Parity : None Stop bits : 1 Flow Control : None At the Login: prompt, type admin and press Enter twice (no password required). Change from NAT/Route mode to Transparent mode. Configure the Management config system settings set opmode transparent set manageip <mng_ip>/<netmask> set gateway <gateway_ip> end Configure the dns config system dns set primary <dns-server_ip> set secondary <dns-server_ip> end